trunk/src/mame/drivers/segac2.c
| r249918 | r249919 | |
|---|
| 937 | 937 | PORT_INCLUDE( systemc_generic ) |
| 938 | 938 | |
| 939 | 939 | PORT_MODIFY("P1") |
| 940 | | PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_NAME("Relay") // relay (must be ON by default or machine will instantly give an 'assistance' error) |
| 940 | PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON3 ) PORT_NAME("Relay") // relay (must be ON by default or machine will instantly give an 'assistance' error) - pressing this advances the stages of operation (from type select, and during the turning of the wheel) |
| 941 | 941 | PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON4 ) PORT_NAME("Coinblock") // coinblock (inverted) |
| 942 | | PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_NAME("Sensor") // sensor |
| 942 | PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON5 ) PORT_NAME("Sensor") // sensor - causes an extra animation to play if you press it during attract and 'Sensor Advertise' dip is on |
| 943 | 943 | PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_UNUSED ) |
| 944 | | PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_START2 ) PORT_NAME("Cup Select 1") // cup select 2 |
| 944 | PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_START2 ) PORT_NAME("Cup Select 2") // cup select 2 - pressing Cup Select 1 and 2 registers as 'Cup Select 3', I presume these are lines from the mechanical part. |
| 945 | 945 | PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_START1 ) PORT_NAME("Cup Select 1") // cup select 1 |
| 946 | 946 | PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_BUTTON2 ) PORT_NAME("Handle B") // handle B |
| 947 | 947 | PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_BUTTON1 ) PORT_NAME("Handle A") // handle A |
| 948 | 948 | |
| 949 | 949 | PORT_MODIFY("P2") |
| 950 | | PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON9 ) PORT_NAME("Sold Out LED1") // sold out LED 1 |
| 950 | PORT_BIT( 0x01, IP_ACTIVE_LOW, IPT_BUTTON9 ) PORT_NAME("Sold Out LED1") // sold out LED 1 - are these actually output lines? |
| 951 | 951 | PORT_BIT( 0x02, IP_ACTIVE_LOW, IPT_BUTTON10 ) PORT_NAME("Sold Out LED2") // sold out LED 2 |
| 952 | 952 | PORT_BIT( 0x04, IP_ACTIVE_LOW, IPT_BUTTON11 ) PORT_NAME("Sold Out LED3") // sold out LED 3 |
| 953 | 953 | PORT_BIT( 0x08, IP_ACTIVE_LOW, IPT_UNUSED ) |
| 954 | | PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_NAME("Sold Out SW2") // sold out SW 2 |
| 954 | PORT_BIT( 0x10, IP_ACTIVE_LOW, IPT_BUTTON7 ) PORT_NAME("Sold Out SW2") // sold out SW 2 - holding these while coining up will show popcorn as unavailable, pressing all 3 will fault the machine |
| 955 | 955 | PORT_BIT( 0x20, IP_ACTIVE_LOW, IPT_BUTTON8 ) PORT_NAME("Sold Out SW3") // sold out SW 3 |
| 956 | 956 | PORT_BIT( 0x40, IP_ACTIVE_LOW, IPT_UNUSED ) |
| 957 | 957 | PORT_BIT( 0x80, IP_ACTIVE_LOW, IPT_BUTTON6 ) PORT_NAME("Sold Out SW1") // sold out SW 1 |